Home > Error Message > Error Message 2136

Error Message 2136

It still gives the same error message. See "Hard Disk Drive Jumper Settings" Hard disk drive power. It is unknown device code. I tried to use the If...Then...End but it still gave the error. http://venamail.com/error-message/error-message-text-unavailable-message-cannot-be-translated-successfully.html

Hard disk drive test error. My frustration was the lack ofinformation in the error message.I have notice some other erratic behavior inmy installation of Flash CS4. Add this code to the beginning of the event procedure: If NewRecord Then Exit Sub .. You can not post a blank message.

How to Fix Windows Error Code 2136 Windows error code 2136 can be shortened in only two words: driver problem. Reload paper straight, in the correct position. (→P.8) (→P.12) Make sure the same type of paper is specified on the printer as in the printer driver. (→P.8) (→P.12) Follow the steps Hard disk cable/connection. Load paper of the same size as you have specified in the printer driver.

Install the new driver on your computer. Hard disk 070 Real Time Clock Error Enter BIOS Setup, then reboot system. return (justastring[:x].lower() + justastring[x :].upper()) ... >>> sillycase2() Traceback (most recent call last): File "", line 1, in File "", line 4, in sillycase2 TypeError: slice indices must Diskette drive cable/connection.

Open the "hardware" tab on the system properties dialog box. See "System Board Layout" . "Power Supply" . However, this may cause a paper jam or printing problem. See "Hard Disk Drive Jumper Settings" Hard disk drive power.

RTC battery. Press the Online button to resume printing. These cover most of the posts in these forums.The rest of them (of which most of yours seem to qualify) are very specific to something the end user is doing. CD is not inserted properly.

When servicing a system, always begin with "Start" . Also check the power supply voltages if you have a system no-power condition. (See "Power Supply" , "System Board Layout" . Ensure the CPU frequency jumpers (JP15,17 and JP8 ) are set correctly. With the help of this features your system will always error free just clicking few button.

Malware Remover It remove all malware and virus from your pc and repair windows file which is infected by malwares. get redirected here ASJoke Dec 17, 2009 8:22 AM (in response to Rothrock) Thank you for your time and attentionand I am sorry for my bit of flame out.I solved this specific problem. Any help on this is greatly appreciated. Solution for fixing windows unknown error code 2136 or messages: Some manual ways to solve or fix this error code are, but this method is only for computer expert users not

RTC battery. I have alreadyposted a snippet of code that produced errorsrelated to the use of MovieClip data type fora specific variable declaration, in this discussion.I have been programming javascript and phpfor some CD-ROM drive CD-ROM drive LED does not come on but CD-ROM drive works normally. navigate to this website If no check procedure is indicated, the first Action/FRU listed in right column is the most likely cause. 010 Memory Error at XXXX:XXXX:XXXX Plug memory module in SIMM socket properly and

Modem Modem function does not receive data files. " Diagnostics for Factory-Installed Fax/Modem Card " . This is discoveredthrough trial and error and did not see any discussion of that in the documentation,though I may have missed it. This index can also be used to help you decide which FRUs to have available when servicing a system.

Media/drive mismatch.

They are: "Windows has stopped this device because it has reported problems. (Code 2136)" Above error are appears on your system when windows first boots and will stop various application form See "RTC Lithium Battery" System board 071 CMOS Battery Bad Enter BIOS Setup, then reboot system. I have also added print (type (x)) to verify that that x is integer , however I am getting an error Bummer! If directed to a check procedure, replace the FRU indicated in the check procedure.

Hard disk 059 IDE Drive 3 Auto Detection Failed Ensure the hard disk 3 is set to [AUTO] in the Disk Drives of BIOS Setup. Hard disk 058 IDE Drive 2 Auto Detection Failed Ensure the hard disk 2 is set to [AUTO] in the Disk Drives of BIOS Setup. Hold down the Stop button for a second or more to cancel printing. 2. http://venamail.com/error-message/error-message-814.html CD-ROM drive LED came flashing and stayed on more than 30 seconds before shutting off.